Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Santa Rosa?
Gate parts and welding work in Santa Rosa typically runs $150 to $650 for common repairs, while a full custom gate fabrication or major structural weld job can land anywhere from $900 to $3,200. Most everyday fixes – a bent hinge, a snapped latch, a cracked weld at the post, a replacement roller or track component – fall in the $180 to $400 range. The written estimate we provide after we look at your gate sets the final price, and that estimate is free.
Answer-First: What You’ll Actually Pay
If your gate needs new hardware and a weld, expect a typical bill between $200 and $450. If the gate frame itself is bent or the post anchor has torn loose, the range climbs toward $600 to $1,400 depending on how much metal has to be cut out and rebuilt. Electric operators, control boards and safety sensors are priced separately from the mechanical and welding side, so a gate with both problems gets two line items in the same estimate.
- Minor hardware (hinges, latches, rollers, stops): $150-$300
- Welding a cracked joint or post anchor: $250-$550
- Track or cantilever rebuild: $450-$900
- Custom frame fabrication: $900-$3,200
Gate Parts & Welding Cost Breakdown (2026)
Here’s how the numbers break down by line item for the Santa Rosa market in 2026. These are typical ranges, not quotes – the written estimate is what governs.
| Item | Typical Price Range |
|---|---|
| Hinge replacement (per hinge, welded or bolt-on) | $90-$220 |
| Latch, handle and lock set replacement | $120-$280 |
| Roller and track hardware (per leaf) | $150-$350 |
| Weld repair, cracked joint or hinge post | $250-$550 |
| Post anchor / footing weld repair | $300-$650 |
| Slide gate track rebuild or straightening | $450-$900 |
| Custom gate fabrication (per leaf, mild steel) | $900-$1,800 |
| Custom gate fabrication (per leaf, aluminum or ornamental) | $1,400-$3,200 |
| Replacement operator motor (parts and install) | $550-$1,200 |
| Control board replacement | $350-$800 |
| Safety sensor or loop detector replacement | $250-$600 |
| Intercom or keypad wiring repair | $200-$500 |
What pushes a job toward the top of a range? Rust and corrosion that has spread into the frame, a gate that’s been dragging for months and has worn the track, and hard-to-source parts for older operators. What pulls it toward the bottom? A single failed component with clean surrounding metal, and a gate that’s still tracking straight. The brand you own matters less than people assume – we work on the brand you already own across LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule, so we’re not steering you toward a replacement because we only know one system.
What Affects Gate Parts & Welding Pricing in Santa Rosa
- Gate material and weight. A light residential aluminum gate welds and hangs differently than a heavy ornamental steel or wrought-iron leaf. Heavier metal means more labor, more reinforcement and higher cost.
- Condition of the post and footing. If the hinge post has pulled out of its footing, we’re welding to something that isn’t stable yet. Stabilizing the post has to come first, and that adds a line item to the estimate.
- Whether it’s an electric gate. On an automated gate, welding and hardware work happens around live wiring, motors and control boards. Electric gate repair is a separate skill set, and a gate that needs both mechanical work and a board diagnosis gets scoped for both.
- Brand and vintage of the operator. Newer LiftMaster and FAAC systems have parts that are easy to source. Older BFT or DoorKing commercial units may need a little more digging to find the right replacement, and that search time is real time.
- Local soil and settling. Santa Rosa’s clay-heavy ground shifts with the wet winters and dry summers, and gate posts take the brunt of it. A gate that binds every spring is often a footing problem, not a hardware problem.
- Gate size and leaf count. A single swing leaf is one job. A double swing or a long cantilever slide gate is two or three times the hardware, the welding and the setup.
- Access and clearance. A gate tucked behind landscaping or set on a slope changes how we get to the weld and how we brace the gate while it’s off its hinges.
How to Save on Gate Parts & Welding
The biggest savings come from catching a problem before it spreads. A hinge that’s starting to sag is a $90 to $220 fix. A hinge that’s been sagging for a year and has torn the weld out of the frame is a $400 to $650 fix. Same gate, different bill.
- Fix the bind, not just the symptom. If the gate drags, find out why before replacing hardware that will just wear out again. Diagnose first, replace only when necessary.
- Keep the track clear. Debris in a slide gate track wears rollers fast. A few minutes with a broom a few times a year saves hardware money.
- Get the diagnosis right the first time. A generalist who guesses at an electric gate problem can cost you twice – once for the wrong part and once for the right one. We’re electric gate specialists, and we diagnose the system before we quote the repair.
- Ask for one estimate that covers everything. If the gate needs a weld and the operator needs a sensor, get both scoped in one visit. One call covers the whole gate.
Estimates are free. Call (888) 298-3409 and we’ll come look at the gate, tell you what’s actually wrong, and put a written price in front of you. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Repair or Replace: Which Makes Sense?
Repair wins in most cases where the gate frame is sound and the failed part is a hinge, latch, roller, weld or a single electronic component. Replace the leaf only when the frame is bent past straightening, rust has eaten through structural tube, or the cost of the repair passes roughly half the price of a new leaf. On the operator side, a control board or motor that’s failed on a system with parts still available is a repair, not a replacement. We don’t push replacements. We fix the system you have and tell you plainly when a repair no longer makes financial sense.
What Does a Gate Parts & Welding Visit Involve?
A technician arrives, identifies the gate type and operator system, and checks the full assembly from the operator board to the hinge pin. That means testing the motor and controls, inspecting the track and rollers, checking the post and footing, and looking at every weld point on the frame. Then you get the diagnosis and a written estimate. Nothing gets welded or replaced until you’ve approved the price. Our technicians have up to 14 years of experience, and every one of them works on gates and nothing else.
For a broader look at what we handle across the city, see gate repair Santa Rosa, and for neighborhood-level detail check our Santa Rosa page.
FAQs – Gate Parts & Welding Cost
How much does it cost to weld a gate in Santa Rosa?
Welding a cracked joint or hinge post in Santa Rosa typically costs $250 to $550, and a post anchor or footing weld runs $300 to $650. The number depends on how much metal has to be cut out and rebuilt and whether the post is stable. Call (888) 298-3409 for an exact quote – estimates are free.
Is it cheaper to repair a gate or replace it?
Repair is almost always cheaper – a $200 to $450 hardware-and-weld job versus $900 to $3,200 for a new fabricated leaf. Replacement only makes sense when the frame is bent past straightening or rust has compromised the structural tube. Call (888) 298-3409 and we’ll tell you honestly which side of that line your gate is on.
How much do replacement gate hinges and hardware cost?
Hinges run $90 to $220 each, latch and lock sets $120 to $280, and roller and track hardware $150 to $350 per leaf. Heavy ornamental steel gates sit at the top of those ranges because the hardware has to carry more weight. Call (888) 298-3409 for a written estimate.
Can you fix an electric gate and weld it in the same visit?
Yes, in most cases. Electric gate repair and mechanical or welding work are scoped together in one estimate so you’re not booking two companies. Control board replacement runs $350 to $800 and safety sensors $250 to $600 on top of any mechanical work. Call (888) 298-3409 to get both looked at in one visit.
Can you come today?
Same-day service is often possible when you call early. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. Call (888) 298-3409 and we’ll book you into the next opening.
Do you work on the brand of gate operator I already own?
Yes. We work on the brand you already own – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule – from residential budget openers up to commercial-grade systems. Brand-neutral diagnostics means we’re not steering you toward a replacement you don’t need. Call (888) 298-3409 to talk through what you have.
Why a Gate Specialist for Parts and Welding
Gate parts and welding sit at the intersection of metalwork and access control, and a general contractor or garage-door company that moonlights in gates usually only knows half of that picture. A gate that won’t close might be a bent hinge, a failed sensor, a misaligned track or a control board fault – and the fix is different in each case. We do only gate work: repair, electric and automated repair, and new installation. That single-trade focus is why we can diagnose a FAAC board and weld a torn hinge post on the same visit without handing you off to a second contractor. From the operator board to the hinge pin, one call covers the whole gate.
Pricing reflects the Santa Rosa market as of 2026. Gate Repair Santa Rosa offers free estimates – call (888) 298-3409. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Santa Rosa.
What Our Customers Say
"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Oscar Castillo"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Norma Garcia"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Christine Kim